Snort FAQ

Snort 2.9 includes a number of changes to better handle inline operation, including:

  • a single mechanism for all responses
  • fully encoded reset or icmp unreachable packets
  • updated flexible response rule option
  • updated react rule option
  • added block and sblock rule actions

These changes are outlined below.


This enables active responses (snort will send TCP RST or ICMP unreachable/port) when dropping a session.

./configure --enable-active-response

preprocessor stream5_global: \
    max_active_responses <max_rsp>, \
    min_response_seconds <min_sec> 

<max_rsp> ::= (0..25)
<min_sec> ::= (1..300)

Active responses will be encoded based on the triggering packet. TTL will be set to the value captured at session pickup.


Configure the number of attempts to land a TCP RST within the session’s current window (so that it is accepted by the receiving TCP). This sequence “strafing” is really only useful in passive mode. In inline mode the reset is put straight into the stream in lieu of the triggering packet so strafing is not necessary.

Each attempt (sent in rapid succession) has a different sequence number. Each active response will actually cause this number of TCP resets to be sent. TCP data (sent for react) is multiplied similarly. At most 1 ICMP unreachable is sent, iff attempts > 0.

./configure --enable-active-response

config response: [device <dev>] [dst_mac <MAC address>] attempts <att>

<dev> ::= ip | eth0 | etc.
<att> ::= (1..20)
<MAC address> ::= nn:nn:nn:nn:nn:nn    
 (n is a hex number from 0-F)

device ip will perform network layer injection. It is probably a better choice to specify an interface and avoid kernel routing tables, etc.

dst_mac will change response destination MAC address, if the device is eth0, eth1, eth2 etc. Otherwise, response destination MAC address is derived from packet. Example: config response: device eth0 dst_mac 00:06:76:DD:5F:E3 attempts 2


Flexresp and flexresp2 are replaced with flexresp3.

  • Flexresp is deleted; these features are no longer available:

    ./configure –enable-flexresp config flexresp: attempts 1

  • Flexresp2 is deleted; these features are no longer available:

    ./configure –enable-flexresp2

    config flexresp2_interface: eth0 config flexresp2_attempts: 4 config flexresp2_memcap: 1000000 config flexresp2_rows: 1000

  • Flexresp3 is new: the resp rule option keyword is used to configure active responses for rules that fire.

    ./configure –enable-flexresp3

    alert tcp any any -> any 80 (content:”a”; resp:; sid:1;)

  • resp_t includes all flexresp and flexresp2 options:

    ::= \ rst_snd | rst_rcv | rst_all | \ reset_source | reset_dest | reset_both | icmp_net | \ icmp_host | icmp_port | icmp_all

REACT CHANGES =============

react is a rule option keyword that enables sending an HTML page on a session and then resetting it. This is built with:

./configure --enable-react

The page to be sent can be read from a file:

config react: <block.html>

or else the default is used:

<default_page> ::= \
    "HTTP/1.1 403 Forbidden\r\n"
    "Connection: close\r\n"
    "Content-Type: text/html; charset=utf-8\r\n"
    "<!DOCTYPE html PUBLIC \"-//W3C//DTD XHTML 1.1//EN\"\r\n" \
    "    \"\">\r\n" \
    "<html xmlns=\"\" xml:lang=\"en\">\r\n" \
    "<head>\r\n" \
    "<meta http-equiv=\"Content-Type\" content=\"text/html; charset=UTF-8\" />\r\n" \
    "<title>Access Denied</title>\r\n" \
    "</head>\r\n" \
    "<body>\r\n" \
    "<h1>Access Denied</h1>\r\n" \
    "<p>%s</p>\r\n" \
    "</body>\r\n" \

Note that the file must contain the entire response, including any HTTP headers. In fact, the response isn’t strictly limited to HTTP. You could craft a binary payload of arbitrary content.

When the rule is configured, the page is loaded and the %s is replaced with the selected message, which defaults to:

<default_msg> ::= \
    "You are attempting to access a forbidden site.<br />" \
    "Consult your system administrator for details.";

Additional formatting operators beyond a single %s are prohibited, including %d, %x, %s, as well as any URL encodings such as as %20 (space) that may be within a reference URL.

This is an example rule:

drop tcp any any -> any $HTTP_PORTS ( \
    content: "d"; msg:"Unauthorized Access Prohibited!"; \
    react: <react_opts>; sid:4;)

<react_opts> ::= [msg] [, <dep_opts>]

These options are deprecated:

<dep_opts> ::= [block|warn], [proxy <port#>]

The original version sent the web page to one end of the session only if the other end of the session was port 80 or the optional proxy port. The new version always sends the page to the client. If no page should be sent, a resp option can be used instead. The deprecated options are ignored.


The block and sblock actions have been introduced as synonyms for drop and sdrop to help avoid confusion between packets dropped due to load (e.g. lack of available buffers for incoming packets) and packets dropped due to Snort’s analysis.